1. The circuit switch has been interrupted
2. The AC contactor circuit has been interrupted
1. Check the circuit switch
2. Check the AC contactor
Motor does not run but makes a humming noise
1. Power phase loss
1. Stop running, check whether the motor is damaged, and check whether the power line is out of phase.
The motor runs but the lift does not go up
1. The motor rotates incorrectly
2. Insufficient hydraulic oil
3. There is air in the pump station, which causes the hydraulic pressure to be unsmooth
4. Sliding valve blocked
5. There is residual material inside the solenoid valve
6. Damaged sealing ring
7. There are other substances left in the front of the oil filter
8. The manual screw of the electromagnetic pressure relief valve is loose 9. The pressure relief valve pair is manually opened 10. The limit switch works or is damaged
1. Change the motor phase
2. Add hydraulic oil
3. Take out the one-way valve and press the up button (pay attention to the interface), until the oil flows out, the one-way valve can be reset. If it is invalid, the auxiliary operation can be repeated.
4. Inspect the seal and seal components and replace.
5. Clean the inside of the solenoid valve
6. Remove the bolts and cabinets connecting the pump station, pull the motor out 30mm and support it with strips. Press the up key and observe the assembly for leaks, replace the retaining ring if there is leakage.
7. Clean the oil filter
8. Tighten the screws
The rate of rise is very slow
1. The sealing ring is damaged
Check seals and seal components and replace
The lift cannot be lowered
1. The electromagnetic pressure relief valve is in a non-electric state
2. The electromagnetic oil drain valve is damaged
3. The internal button switch is not properly connected
4. Insufficient air pressure
1. Check whether the lower button and solenoid oil drain valve circuit are closed
2. Check the solenoid oil drain valve and repair it
3. Check the switch button
4. Adjust the air pressure and open the mechanical lock
Lifting weight
4000kg
Platform length
1550mm
Lifiting height
1200mm~1800mm
Lifting time
25s~30s
Min. height
110mm
Voltage
220v/380v/etc
Platform width
530mm~635mm
Power
2.2KW
а) Основная структура ультратонкая, требования к пространству невелика, установка грунта удобна для технического обслуживания и обработки, но она также может быть установлена в земле. Стол для ножничного автомобиля
б) Принятие структуры двойных синхронизирующих нефтяных цилиндров, он может поднимать мелкие и средние автомобили. Automech Car Scissor Lift
C) Тройная защита безопасности: гидравлическая блокировка двойного тандемного масляного цилиндров, гидравлическое самозащитное и безопасное механическое блокировка. Гидравлический автомобильный ножничный подъемник
D) Внешнее выравнивание устройства, легко управлять, выровнять и быстро настраивать. Автомобиль ножницы подъемник Брисбен
e) Гидравлическая система принимает итальянский соленоидный клапан и импортируемые компоненты герметизации для обеспечения долгосрочного использования и стабильности.
f) Когда мощность отключена, гидравлическая система может использовать ручную работу для снижения машины. Автомобиль ножницы для лифта Bendpak
Эта машина состоит из четырех частей: механическая часть, гидравлическая система, пневматическая система и электрическая система. Автомобиль ножницы Джек Баннингс
Privacy statement: Your privacy is very important to Us. Our company promises not to disclose your personal information to any external company with out your explicit permission.
We will contact you immediately
Fill in more information so that we can get in touch with you faster
Privacy statement: Your privacy is very important to Us. Our company promises not to disclose your personal information to any external company with out your explicit permission.